From: Alan Toops (alantoops_at_cs.com)
Date: Thu Apr 03 2003 - 11:21:08 PST
Laurent,
Thanks for the quick reply. My setups are just like you described for
both ABS and DSL. I have also set up home and work configs in Internet
services but still get the DNS error, Regardless of manual or DHCP
set-up.
Both wireless stations operate as local DHCP servers and all my gear
(macs and pc's) get an assigned IP address from the station.
Any ideas?
Alan Toops
-----Original Message-----
From: newtontalk-bounce_at_newtontalk.net
[mailto:newtontalk-bounce_at_newtontalk.net] On Behalf Of Laurent Daudelin
Sent: Thursday, April 03, 2003 2:12 PM
To: NewtonTalk
Subject: Re: [NTLK] Soybo and a newbie
On 03/04/03 13:06, "Alan Toops" <alantoops_at_cs.com> wrote:
> Hi,
>
> I am impressed with the potential of Soybo and the way this list
> responds to newbie's like me. Great stuff. I just purchased a MP 2100
> with the Lucent silver wireless card, thanks to the list I was able to
> get NIE 2.0, Hiroshi's drivers and the card to work.
>
> Now one question on configuring, whether I select DHCP or Manual
config,
> I still get a "DNS server not responding, check address.." I have a
snow
> airport at home and an SMC wireless at work?
>
> Any ideas what I have missed?
Well, to use DHCP on your Newton, you have at least to tell him what
your
DHCP server IP address is. With your setup, when you're home, you should
use
an internet setup that will specify the DHCP server IP address to your
ABS
IP address, assuming that it is configured to serve addresses on your
internal network. Then, you would have another setup for when you're at
work, this time specifying the IP address of your SMC wireless router,
this
again, assuming that the router is serving IP addresses or acting as the
DHCP server. Once you have those 2 internet setups working, create or
modify
existing worksites that you will tie to those 2 setups. So, when you go
to
work, switch to your work worksite and the right internet setup will be
made
active.
One thing to watch for is that it could be possible that both your ABS
and
the SMC router are just relaying the packets from the real DHCP server.
It's
hard to tell without having all the details about your setup.
FIY, I have DSL at home. I have a Linksys router that acts as a gateway
between my ISP network and my own network. The router is configured as
the
DHCP server. So, in the router config, I setup it up to get its address
on
my ISP provided from my ISP's DHCP server. Then, my router distributes
IP
addresses to the computers on my network. When one of my computer makes
a
request to the internet, my router acts as a gateway. It forwards the
packet
to the internet. When the response comes back, it is sent to my router,
which has the only IP addresses visible from the internet, and then the
router is able to determine which computer on my network made the
initial
request and routes the incoming response to that computer transparently.
I also have an ABS, but since I already have a DHCP server on my
network,
the ABS merely forward incoming packets from/to the Ethernet network to
AirPort computers. Usually, my laptop that I can connect to the Ethernet
network or to my ABS will receive the same IP address from my router's
DHCP
server. The ABS is just a gateway.
Hope that helps!
-Laurent.
-- ======================================================================== === Laurent Daudelin Developer, Multifamily, ESO, Fannie Mae mailto:Laurent_Daudelin_at_fanniemae.com Washington, DC, USA ************************* Usual disclaimers apply ************************* -- This is the NewtonTalk list - http://www.newtontalk.net/ for all inquiries List FAQ/Etiquette/Terms: http://www.newtontalk.net/faq.html Official Newton FAQ: http://www.chuma.org/newton/faq/ -- This is the NewtonTalk list - http://www.newtontalk.net/ for all inquiries List FAQ/Etiquette/Terms: http://www.newtontalk.net/faq.html Official Newton FAQ: http://www.chuma.org/newton/faq/
This archive was generated by hypermail 2.1.5 : Sat Apr 05 2003 - 20:52:25 PST